Articles in this section

How to upgrade ShMC F/W on PAC-6009 ?

Avatar
Darryl Hsu
  • Updated
Follow

Purpose

This guide is to provide a simple step-by-step guidance for users to follow on How to upgrade ShMC F/W on PAC-6009.

Applicable model list

PAC-6009

Procedure 

A. For PAC-6009 F/W upgrade procedure, you need to use external PC/x86 client to upgrade/rollback the      F/W via LAN. Please follow below diagram to setup the environment.

mceclip0.png

 

Step 1: Please login to ShMC via console and check the IP address. Assume upper ShMC is at Active                      status, if upper ShMC is not at Active status, please change console cable to lower ShMC console              port.

CLI> lan 0x10 list
+==================================================================+
|Channel |IP Address |Subnet Mask |Default Gateway|MAC Address |
+==================================================================+
| 1|192.168.001.254|255.255.255.000|000.000.000.000|74:FE:48:14:FD:D7|
| 2|192.168.002.001|255.255.255.000|000.000.000.000|74:FE:48:14:FD:D8|
| 3|000.000.000.000|255.255.255.000|000.000.000.000|00:0B:AB:00:01:01|
+==================================================================+
CLI> lan 0x12 list
+==================================================================+
|Channel |IP Address |Subnet Mask |Default Gateway|MAC Address |
+==================================================================+
| 1|192.168.001.253|255.255.255.000|000.000.000.000|74:FE:48:14:FD:D9|
| 2|192.168.002.002|255.255.255.000|000.000.000.000|74:FE:48:14:FD:DA|
+==================================================================+

Step 2: Login to your PC/x86 client and then set the IP address in the same network section.

[root@1010 ~]# ifconfig eth3 192.168.1.10
[root@1010 ~]# ping 192.168.1.254
PING 192.168.1.254 (192.168.1.254) 56(84) bytes of data.
64 bytes from 192.168.1.254: icmp_seq=1 ttl=64 time=0.360 ms
^C
--- 192.168.1.254 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.360/0.360/0.360/0.000 ms
[root@1010 ~]# ping 192.168.1.253
PING 192.168.1.253 (192.168.1.253) 56(84) bytes of data.
64 bytes from 192.168.1.253: icmp_seq=1 ttl=64 time=0.361 ms
^C
--- 192.168.1.253 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.361/0.361/0.361/0.000 ms

Step 3: Execute HPM check via IPMItool over LAN. Make sure the IPMItool is working first.

[root@1010 ~]# ipmitool -I lanplus -H 192.168.1.254 -U administrator -P advantech hpm check
PICMG HPM.1 Upgrade Agent 1.0.9:
-------Target Information-------
Device Id : 0x77
Device Revision : 0x81
Product Id : 0x9002
Manufacturer Id : 0x2839 (Advantech)
--------------------------------------------------------------------------
|ID | Name | Versions |
| | | Active | Backup | Deferred |
--------------------------------------------------------------------------
| 0|9002 BL | 1.00 00000000 | ---.-- -------- | ---.-- -------- |
| 1|9002 SHMC | 1.04 00000000 | 1.04 00000000 | ---.-- -------- |
| 2|9002 FPGA | 1.00 00000000 | ---.-- -------- | ---.-- -------- |
| 3|9002 CPLD | 144.02 00000000 | ---.-- -------- | ---.-- -------- |
--------------------------------------------------------------------------
(*) Component requires Payload Cold Reset
[root@1010 ~]# ipmitool -I lanplus -H 192.168.1.253 -U administrator -P advantech hpm check
PICMG HPM.1 Upgrade Agent 1.0.9:
-------Target Information-------
Device Id : 0x77
Device Revision : 0x81
Product Id : 0x9002
Manufacturer Id : 0x2839 (Advantech)
--------------------------------------------------------------------------
|ID | Name | Versions |
| | | Active | Backup | Deferred |
--------------------------------------------------------------------------
| 0|9002 BL | 1.00 00000000 | ---.-- -------- | ---.-- -------- |
| 1|9002 SHMC | 1.04 00000000 | 1.04 00000000 | ---.-- -------- |
| 2|9002 FPGA | 1.00 00000000 | ---.-- -------- | ---.-- -------- |
| 3|9002 CPLD | 144.02 00000000 | ---.-- -------- | ---.-- -------- |
--------------------------------------------------------------------------
(*) Component requires Payload Cold Reset

Step 4: Please put the new firmware to your PC/x86 client first. Execute Upper side ShMC
firmware upgrade via IPMItool over LAN.

[root@1010 ~]# ipmitool -I lanplus -H 192.168.1.254 -U administrator -P advantech hpm
upgrade $file_name activate

Step 5: After side ShMC firmware upgrade successfully. Please execute lower side ShMC
firmware upgrade via IPMItool over LAN again.

[root@1010 ~]# ipmitool -I lanplus -H 192.168.1.253 -U administrator -P advantech hpm
upgrade $file_name activate

Step 6: Execute HPM check via IPMItool over LAN. Make sure the firmware version is correct.

[root@1010 ~]# ipmitool -I lanplus -H 192.168.1.254 -U administrator -P advantech hpm check
PICMG HPM.1 Upgrade Agent 1.0.9:
-------Target Information-------
Device Id : 0x77
Device Revision : 0x81
Product Id : 0x9002
Manufacturer Id : 0x2839 (Advantech)
--------------------------------------------------------------------------
|ID | Name | Versions |
| | | Active | Backup | Deferred |
--------------------------------------------------------------------------
| 0|9002 BL | 1.00 00000000 | ---.-- -------- | ---.-- -------- |
| 1|9002 SHMC | 1.09 00000000 | 1.04 00000000 | ---.-- -------- |
|* 2|9002 FPGA | 1.00 00000000 | ---.-- -------- | ---.-- -------- |
| 3|9002 CPLD | 144.02 00000000 | ---.-- -------- | ---.-- -------- |
--------------------------------------------------------------------------
(*) Component requires Payload Cold Reset
[root@1010 ~]# ipmitool -I lanplus -H 192.168.1.253 -U administrator -P advantech hpm check
PICMG HPM.1 Upgrade Agent 1.0.9:
-------Target Information-------
Device Id : 0x77
Device Revision : 0x81
Product Id : 0x9002
Manufacturer Id : 0x2839 (Advantech)
--------------------------------------------------------------------------
|ID | Name | Versions |
| | | Active | Backup | Deferred |
--------------------------------------------------------------------------
| 0|9002 BL | 1.00 00000000 | ---.-- -------- | ---.-- -------- |
| 1|9002 SHMC | 1.09 00000000 | 1.04 00000000 | ---.-- -------- |
|* 2|9002 FPGA | 1.00 00000000 | ---.-- -------- | ---.-- -------- |
| 3|9002 CPLD | 144.02 00000000 | ---.-- -------- | ---.-- -------- |
--------------------------------------------------------------------------
(*) Component requires Payload Cold Reset

B. Rollback ShMC procedure

Step 1: Execute HPM rollback via IPMItool over LAN for Upper side ShMC.

[root@1010 ~]# ipmitool -I lanplus -H 192.168.1.254 -U administrator -P advantech hpm rollback

Step 2: Make sure the firmware version is rollback successfully for Upper side ShMC.

[root@1010 ~]# ipmitool -I lanplus -H 192.168.1.254 -U administrator -P advantech hpm check
PICMG HPM.1 Upgrade Agent 1.0.9:
-------Target Information-------
Device Id : 0x77
Device Revision : 0x81
Product Id : 0x9002
Manufacturer Id : 0x2839 (Advantech)
--------------------------------------------------------------------------
|ID | Name | Versions |
| | | Active | Backup | Deferred |
--------------------------------------------------------------------------
| 0|9002 BL | 1.00 00000000 | ---.-- -------- | ---.-- -------- |
| 1|9002 SHMC | 1.04 00000000 | ---.-- -------- | ---.-- -------- |
|* 2|9002 FPGA | 1.00 00000000 | ---.-- -------- | ---.-- -------- |
| 3|9002 CPLD | 144.02 00000000 | ---.-- -------- | ---.-- -------- |
--------------------------------------------------------------------------
(*) Component requires Payload Cold Reset

Step 3: Execute HPM rollback via IPMItool over LAN for Lower side ShMC.

[root@1010 ~]# ipmitool -I lanplus -H 192.168.1.253 -U administrator -P advantech hpm rollback

Step 2: Make sure the firmware version is rollback successfully for Lower side ShMC. 

[root@1010 ~]# ipmitool -I lanplus -H 192.168.1.253 -U administrator -P advantech hpm check
PICMG HPM.1 Upgrade Agent 1.0.9:
-------Target Information-------
Device Id : 0x77
Device Revision : 0x81
Product Id : 0x9002
Manufacturer Id : 0x2839 (Advantech)
--------------------------------------------------------------------------
|ID | Name | Versions |
| | | Active | Backup | Deferred |
--------------------------------------------------------------------------
| 0|9002 BL | 1.00 00000000 | ---.-- -------- | ---.-- -------- |
| 1|9002 SHMC | 1.04 00000000 | ---.-- -------- | ---.-- -------- |
|* 2|9002 FPGA | 1.00 00000000 | ---.-- -------- | ---.-- -------- |
| 3|9002 CPLD | 144.02 00000000 | ---.-- -------- | ---.-- -------- |
--------------------------------------------------------------------------
(*) Component requires Payload Cold Reset

Comments

0 comments

Please sign in to leave a comment.